Earthquake Sound Wzmacniacz stereo 16IR Instrukcja obsługi

Cinénova IR16

8-ZONES MULTI-SOURCE

IR DRIVEN AMPLIFIER

USER’S MANUAL

Earthquake Sound Corporation

2727 McCone Avenue. Hayward, CA 94545

Phone: 510-732-1000

Fax: 510-732-1095

www.earthquakesound.com

Sound That Will Move You.

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Cinénova-IR16 Power Amplifier

Table of Content

Getting Started

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Basic Operations

Front & Rear Panel Overview . . . . . . . . . . . . . . . . . . . . . . . . . .

Front Panel Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rear Panel Map - LOCAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Rear Panel Map - BUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Keypad & Remote Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Special Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Features Explained . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

IR Wiring Configuration Sample . . . . . . . . . . . . . . . . . . . . . . . . 15

Recommended Configuration . . . . . . . . . . . . . . . . . . . . . . . . 16

Specifications

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Troubleshooting & Maintenance

Troubleshooting & Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 18

Product Warranty

Product Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Earthquake Sound

Safety Instructions

Safety First

This documentation contains general safety, installation, and operating instructions for the Cinénova-IR16 Amplifiers. It is

important to read this users’ manual before attempting to use these products. Pay particular attention to the safety

instructions.

Symbols Explained:

Appears on the component to indicate the presence of uninsulated, dangerous voltage inside the enclosure –

voltage that may be sufficient to constitute a risk of shock.

Calls attention to a procedure, practice, condition or the like that, if not correctly performed or adhered to, could result

in injury or death.

Calls attention to a procedure, practice, condition or the like that, if not correctly performed or adhered to, could result

in damage to or destruction of part or all of the product.

Note:

Calls attention to information that is essential to highlight.

This document should not be construed as a commitment on the part of Earthquake Sound Corporation. The information is subject to change without notice.

Earthquake Sound Corporation assumes no responsibility for errors that may appear within this document.

The Sound That Will Move You.

Earthquake Sound Corporation

2727 McCone Avenue

Hayward, CA 94545

Tel: 510-732-1000

Fax: 510-732-1095

Customer Support

[email protected]

Tel: 800-576-7944

Fax: 510-732-1095

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Cinénova-IR16 Power Amplifier

Safety Instructions

Important Safety Instructions

1) Read these instructions in their entirety.

10) Protect the power cord from being walked on or pinched,

particularly at plugs, convenience receptacles, and the pint

where they exit from the apparatus.

2) Store this manual and packaging in a safe place.

3) Heed all warnings.

11) Only use attachments & accessories specified by the

manufacturer.

4) Follow instructions (do not take short cuts).

5) Do not use this apparatus near water.

6) Clean only with a dry cloth.

12) Use only compatible rack or cart for final resting position.

13) Unplug this apparatus during lighting storm or when unused

for long period of time.

7) Do not block any ventilation openings. Install in accordance

with the manufacturers instructions.

14) Refer all servicing to qualified service personal. Servicing is

required when the apparatus has been damaged in any way

such as; power-supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatuses that produce heat.

9) Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider that the other. A grounding-type plug has two

blades and a third grounding prong. The wide blade or the

third prong is provided for your safety. If the provided plug

does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

15) To reduce the risk of fire or electric shock, do not expose

this apparatus to rain or moisture.

This triangle, which appears on your component,

alerts you to important operating and

maintenance instructions in this

alerts you to the presence of uninsulated,

dangerous voltage inside the enclosure -

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

voltage that may be sufficient to

constitute a risk of shock.

accompanying literature.

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Earthquake Sound

Introduction

About Cinénova-IR16

The Cinénova-IR16 is the second generation in multi-zone that Earthquake has produced. Thanks to the feedbacks received from custom home

installers worldwide, we have managed present you with a truly powerful yet audiophile multi-zone amplifier with the following features:

Bridgeable output

Zone IR control with digital pad in each zone (included)

Décor friendly keypad

Four (4) built-in IRrepeaters

Rear gain control limiter which limits the output gain of the zone pad.

Each zone has a LOCAL/BUS input audio selector

12V DC trigger

Individually driven amplifier blocks (each block is driven by a discrete complementary output classA/Bstage with selected components)

Individual power supplies(bifilars) for power isolation, accuracy and better channel separation

There is no other multi-zone amplifier on the market with such features and power. Enjoy.

Over the years, many of you have provided us with design requirements, new product development ideas and tremendous

feedback that helped us to improved our products. We are very grateful for your support and feedback.

From all of us here at Earthquake Sound Corporation: Thank you.

Professor Joseph J. Sahyoun

President & Chief Engineer

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Cinénova-IR16 Power Amplifier

Unpacking

Connection tips

Unpacking system components

Keep the original carton and packing materials for future

shipment or storage.

It is recommended that the Cinénova-IR16 and the source

equipment be plugged into a dedicated 20-amp circuit with an

isolated ground.

! Check for any visual signs of damage. If you encounter any

concealed damage, consult your Earthquake Sound dealer

before proceeding with unit installation.

Disconnect all live power cords before making connections to the

remote gain.

! Retain the sales receipt as it established the duration of the

limited warranty and provided information for insurance

purposes.

Keep all power cords away from all signal cables to prevent

humming from induced noise.

! Choose reliable signal cables cords (Earthquake Sound also

Cinénova-IR16 included components

• 1 Power cord

specializes in high-performance RCA cables and patches).

• 8 Remote controls

! All speaker wires that are ran through the walls should be twisted

• 8 Keypads (wallplates not included)

• 8 Phoenix speaker terminals

• 8 Phoenix pad connectors

• 1 16-channelAmplifier

type to reduce potential hum noise pick up.

! Label both ends of all wires with the corresponding room

location.

! It is best to use a grounded electrical outlet to power the

amplifier. Lack of input ground reference could be unsafe.

Consult with your electrical contractor about proper grounding.

System installation considerations

There are several factors to consider before installing the Earthquake

Sound Cinénova-IR16 system.

• What are the intended listening zones?

• What system options and accessories might be required for

features such as local sources, etc.?

• From where in each zone will the listener prefer to control the

system? Where will the remote gains be located? Where will the

speakers be located?

• Where will the source equipment be located?

Note: The Cinénova-IR16 must have adequate ventilation above and

below for air circulation and heat dissipation. In addition, rack mount

locations may require fans and vents.

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Earthquake Sound

Front & Rear Panel Overview

19” (482.6mm)

Cinénova

C to C 18.375” (466.5mm)

17” (431mm)

SPEAKER OUTPUT

FUSE

110-120VAC-60Hz

220-240VAC-50Hz

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Cinénova-IR16 Power Amplifier

Front Panel Map

Front Panel

Cinénova

1 Power/StandbySwitch

This red colored LED indicates whether the amplifier is ONor OFF. When the amplifier is ON, this LED will be lit.

Note: When using the rear 12V DCTrigger (page 11 -feature 11), this front switch must be turned OFF.

2 FrontPanelPowerLED

This LED reflects the power statusof the whole amplifier.Amplifier will not have any output unless this LED is ON.

Note: When using another device to turn on the Cinénova IR16 amplifier, this LED will come on when external device sends DC signal (between 5 and 28V

DC) tothe back ofTrigger connector (page 11 -feature 11).

Peak LEDIndicators

Each LED represents one (1) channel.This particular model has sixteen (16) channels.Thus, there are sixteen (16) LEDs located on the front panel.

(!) Cinénova IR16 can be mounted in a standard rack mount (4 rack spaces).

(!) Mounting Dimensions: 4” center to center vertical and 18.37” center to center wide.

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Earthquake Sound

Rear Panel Map - LOCAL

1 Level Controls

This feature adjusts the maximum desired output of the associated zone to prevent overpowering of small

speakers.

Note:This knob is by-passed when itszone selector switch(feature 2) is set toBUS.

LEVEL

0.2V

LOCAL/BUSSwitch

It switches the audio source between LOCALand common BUS. In LOCALmode, the zone acts independently

from the rest of system by only amplifying the information fed through the associated RCAinputs. In BUS mode,

that particular zone will amplify the signal fed through the main BUS input (page 11 -feature 9).

LOCAL

BUS

3 AudioRCAInput

Individual stereo RCA inputs to drive signal into associated zones. Both RCA’s, LEFT and RIGHT, are active

when the STEREO/MONOswitch is set toMONO(feature 4).Thus, you can use either RCAinputs.

Note: This RCA input also serves as an Auto Signal Sensing whenever there is a signal greater than 12mV

present.

STEREO

MONO

IR IN

STEREO/MONOSelector

Switches the amplifier’soutput between STEREOor MONO.

·In STEREO mode, the LEFT and RIGHT outputs operate independently at 75 Watts per channel at 4Ù

speaker load. Level, Gain,AutoTurn ONand MUTEare all common toboth.

·In MONO mode, the LEFT and RIGHT stereo signals are summed internally for a single high power output.

You can drive two 4Ù speakers in this mode or a single 4Ù Bridged for maximum power of 150WRMS.Also, if

the source is already a mono signal, you may use either RCA, LEFTor RIGHT.

STATUS

GROUND

Keypad/ZoneConnector

With four (4) removable conductors (IR IN, STATUS, GROUND and CI–Control Input), these screw type

connector accepts wire sized from 24 to 12 AWG. We recommend using the CAT5, CAT5E, CAT6 or CAT6E

wires.

·IR IN – receive all types of IR signal transmitted through the Earthquake Keypad. It allows Volume up/down

and mute function at the local amplifier. Also, it allows most IR signal to pass through the four built-in IR

repeaters of the Cinénova 16IR (page 11 -feature 12).

FFI

BRIDGE

·STATUS – this connector delivers DC signal to the Keypad’s LED status indicator when the associated

amplifier is ON.

·GROUND – forthe Keypad.

·CI– Control Input is the communicator line used tocontrol amplifier’sON/OFF(Mute) statusmanually.

FaultFuseIndicator(FFI)

This LED indicates the safe operation of the amplifier’s internal circuit for the associated zone. Under normal

condition, this LED is off. When it is lit, the fuse on the internal circuit of that associated zone is blown, usually

due to a shorted circuit. Simply replace with the same size fuse. For your convenience, we’ve included four (4)

additional fuses with every amplifier.

SPEAKER OUTPUT

Speaker Terminals

This screw type connector with four (4) removable conductors accepts wire sizes from 16 to 12AWG. Observe

the Polarity printed on the terminal. Observe the printed instruction above and below the Speaker terminal.

FUSE

110-120VAC-60Hz

220-240VAC-50Hz

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Cinénova-IR16 Power Amplifier

Rear Panel Map - BUS

8 CommonBUS LevelController

This potentiometer controls the output level on all individual amplifiers that are switched to BUS mode. It also

actsas a volume limiter toprotect the speakers and amplifier itself.

9 CommonBUSAudioRCAInput

LEVEL

This pair of RCAdrives a stereo signal into all zones that are switched to BUS mode. It allows one (1) source to

control as many as 8 zones’audio out.

0.2V

BUS

10 RCALineOut

This allows the audio signal applied to the BUS RCA inputs to pass through unaltered to another device in the

system.

11 12V DC Trigger

LINE OUT

It is the remote turn on option driven by a controlled 12V DC source or anAC/DC converter. The relay operating

range is between 5V DC and up to 28V DC. This remote turn on option does not override the auto signal sensing

turn on feature of this amplifier.

Note: The front power switch (page 9 - feature 1) must be left in the OFF position in order to for this function to

+12VDC

TRIGGER

work.

IROutputs

Four (4) amplified IRrepeaters torepeat signals and commends fed through individual Earthquake Keypads.

IR OUT

PowerConnection

This three (3) prongAC line connector is factorypreset to120VAC. However, other voltages are also available.

MainPowerFuse

Always replace the protection fuse with a similar value fuse. Please follow the fuse rating below:

115V,T15AL/250V

230V,T10AL/250V

FUSE

110-120VAC-60Hz

220-240VAC-50Hz

SPEAKER OUTPUT

FUSE

110-120VAC-60Hz

220-240VAC-50Hz

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Earthquake Sound

Keypad & Remote Map

1 LEDStatus

This red colored LED indicates whether the amplifier is ONor OFF. When the amplifier is ON, this LED will be lit.

2 VolumeUp/Down

This allows you to manually control the volume level up or down. The volume increases and decreases at the

same rate.

Note: This amplifier will hold the user defined volume setting for up to 3 hours from the last shut down.

Otherwise, the amplifier will start with volume position set to minimum to prevent undesired loud music in

unattended areas.

Mute

This allows you tomute or un-mute the associated amplifier(s) output.

IRReceiver

This feature allows the communication of all IR information between the Keypad and the rest of the system.

Coded signal controls the individual volume at each channel while other IR information can pass through

unaltered tothe rest of the components connected tothe provided IRout repeaters (page 11 -feature 12).

Note: Wallplates are not included

(!) NOTE: One Keypad is capable of driving multiple zones. Simply connect the CI wire of those zones in

parallel. For example, if you want to use the Keypad from zone 1 to control zone 1 through 5, remove the

Keypad connecting wires from zone 2 through 5 and parallel the CI wire of zone 2 through 5 to the CI of

zone1.

(!) NOTE: If a zone is not connected to a Keypad, the speaker output will be muted (no audio output to

thespeaker) unlessyouparallelconnectthatzone’s CIwiretoanotherzone’s CI.

KEYPAD

KEYPAD KEYPAD KEYPAD

ZONE

MUTE

VOL+

VOL-

In addition to the eight (8) Earthquake Keypads, we also provide you with remote controls that have the same

functions – Volume Up/Down and Mute. For your convenience, the remote information can be taught to any

remote with learning capability.

1 Mute

This allows you tomute or un-mute the associated amplifier(s) output.

2 VolumeUp/Down

This allows you to manually control the volume level up or down. The volume increases and decreases at the

same rate.

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Cinénova-IR16 Power Amplifier

Special Features

Eightindividualpowersupplies:

Rack mountable:

This amplifier is designed to conveniently mount in commonly

The Cinénova-IR16 is designed with 8 individual power

supplies(bifilar) for power isolation, accuracy and better channel

separation.

used racks.

Peak LEDindicators:

110VAC and220VAC selectable:

The Cinénova-IR16 is equipped with 16 LED indicators on the

front panel. They show the operating status of each channel; the LEDs

will illuminate when the maximum recommended output is exceeded.

If an LED is illuminated the majority of the time, it indicates that the

corresponding channel is over-driven (clipped). The input to the

channel must be reduced to eliminate distortion and eventually,

damages tothe amplifier.

The Cinénova-IR16 is factory preset to 110-120VAC. However,

it can also be set to accommodate 220-240VAC by Earthquake

authorized technician(s)/dealer(s).

Remote zonecontrol:

Each of the eight possible zones can be controlled by a wireless

IR remote control. Each remote has the ability to control volume’s

up/down level, mute and also repeat the IRsignal toother sources.

Thermal protection:

Each channel is equipped with a thermal sensor designed to

shut the amplifier down when it overheats. Overheating is not typical. It

only occurs if the amplifier is over driven with low impedance speakers,

or if the amplifier is located in an improperly ventilated space.

Bus input:

This feature simplifies installation by consolidating several

channels for one source. Simply plug the input source RCAs into the

BUS input on the unit. Then switch the input source selector to BUS for

as many channels are connected tothe corresponding input source.

Individuallyselected andmatched components:

Components used to construct the Cinénova-IR16 are

subjected to an exhaustive selection process; during which, the

components are matched and individually tested to exact tolerance.

The multi-layer, glass-epoxy, double sided printed circuit boards

exceed the standard stringent requirements by 50%.

Bridgeablefunction(minimumimpedance =4-ohm):

The Cinénova-IR16 delivers up to 8-zones, and can be bridged

into several different configurations forhigher power rooms.

4 or8-ohmcompatible:

8-Zones:

Since speakers are manufactured in several different

impedance ratings, Earthquake Sound’s Cinénova-IR16 amplifier is

designed tobe 4 and 8-Ohm compatible.

The Cinénova-IR16 delivers up to 8-zones, and several other

room combinations tobetter suite the your needs.

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Earthquake Sound

Features Explained

SPEAKER OUTPUT

FUSE

110-120VAC-60Hz

220-240VAC-50Hz

Amplifier section Explained

BUS section Explained

Rear Gain Control Limiter (RGCL)

It controls the front pad maximum output power from over

powering small speakers. The module RGCLwill limit the

output only when the RCA input selection is set to MAIN

(not Bus).

Bus Control Limiter (BCL)

It controls the front pad maximum output power

from over powering small speakers. The module

BCL would limit the output power of any amplifier

that uses the bus as a signal source.

Input Signal Control(ISC)

When switched to LOCAL, individual

inputs will drive each individual

amplifier.

When selecting BUS, the audio

input from the BUS will drive the

amplifier.

Bus RCA input signal

Stereo input signal RCAthat delivers the signal to

the bus. It also allows you do daisy chain the

signal toadditional Cinénova amplifiers.

Keypad Front view

Mono/ Stereo input control

You must switch to MONO when the amplifier

is wired for MONO

DC TRIGGER

12 Volt DC trigger to be connected to source

output 12 volt trigger. For this to operate, you need

toswitch the front panel switch to OFF.

Phoenix type connector

Should be wired using CAT5 or 5e, CAT6 or 6e.

This allows zone control via IR. This must be

connected tothe zone pad.

4 IR repeater

Speaker output terminal

The Cinénova-IR16 has four output IR that

combine any or all zone IR input. These repeater

will repeat the sum of IR signal to control any

source input. Please note that you will need to use

your source remote, aim it at the pad and it will

deliver the IRsignal to the source.

For stereo applications, please follow the

polarity that is shown on top. For MONO

follow the bottom polarity.

Please note that FFI is

Fault Fuse

Keypad Rear view

Indicator. Any amplifier that has the FFI

LED light on will require a fuse replacement

or possibly service.

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Cinénova-IR16 Power Amplifier

The Cinénova 16 IR allows you to connect several sources to the input stage of the amplfier. It also allows you to aim the remote

IR Wiring Configuration Sample

at the zone pad and use the source remote control. As you aim the remote to the pad, the IR signal is transmitted from the pad to

the amplifier and thereafter amplified. There are four repeaters on the back of the amplifier that can be connected to the source IR

sensor. Once connected, the user can control the source from the room. the illustration below has a DVD player connected to the

IR repeater. Please note that the remote in use is that of the DVD player.

SPEAKER OUTPUT

repeater

FUSE

110-120VAC-60Hz

220-240VAC-50Hz

Keypad Front view

Source:DVD player

Keypad Rear view

Remote:DVD player

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Earthquake Sound

Recommended Configuration

SPEAKER OUTPUT

FUSE

110-120VAC-60Hz

220-240VAC-50Hz

150 Watts RMS/Per Channel

1-High Power Zones

MONO/Bridged

75 Watts RMS/Per Channel

Background room(s)

6-Zones STEREO

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Cinénova-IR16 Power Amplifier

SPECIFICATIONS

Specifications

• Number of channels

16 Channels

• Dimensions

Face plate (W x D x H): 19” (482.6mm) x 0.47” (12mm) x 6.87” (174.5mm)

Mounting (W x H): 18.37” (466.5mm) x 4” (101.5mm)

• Power rating per channel

(4-Ohm stereo), all channels driven:

(4-Ohm bridged), 8 channels:

(8-Ohm stereo), all channels driven:

(8-Ohm bridged), 8 channels:

75 Watts RMS

150 Watts RMS

50 Watts RMS

100 Watts RMS

Chassis (W x D x H): 16.65” (423mm) x 17” (405mm) x 6.71” (170.5mm)

W_C

D_C

• Frequency response:

20Hz - 20kHz at -0.3dB

0.01%

H_C

• Total Harmonic Distortion - THD:

• Input sensitivity (for rated output power):

W_M

H_F

H_M

200mV - 3V

Cinénova

• Input impedance

Independent channels

Bus Input

W_F

22 kÙ

70 kÙ

• Signal to noise ratio:

• AUTO OFF delay time:

• Crosstalk:

92dB

12 minutes

>86dB

• Slew rate:

50V/ì sec

FOR YOUR RECORDS

• Gain:

• Damping Factor:

• Remote trigger voltage:

> 200 @ 8Ù

5.5 - 28 VDC

Date of purchase:

Serial number:

_________________________________

( _______ ) ________ - _____________

• Power requirement:

15 Amp 120VAC 60Hz / 10 Amp 220VAC 50Hz

Authorized dealer name:

Dealer’s address:

• Fuse ratings:

Main power fuse:

Block fuse:

115V,T15A/250V / 230,T10A/250V

3 AG type, slow blow 5A/250V

• Weight

Net weight:

Gross weight:

61.7 lbs / 28 kg

66.1 lbs / 30 kg

Dealer’s phone number:

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Earthquake Sound

Troubleshooting and Maintenance

Troubleshooting

Maintenance

The following routine maintenance should be performed on a periodic

basis:

Humming noise from speakers.

Often humming noise is emanating from equipments that

have their ground prong broken.

?Clean the exterior surfaces of the unit with a soft, dry, lint-free cloth.

?Do not use alcohol, benzene, acetone-based cleaners, or strong

commercial cleaners.

?Do not use a cloth made with steel wool or metal polish.

?If the unit is exposed to a dusty environment, a low-pressure

blower may be used to remove dust from its interior & exterior.

a) With the amplifier OFF, unplug all RCAs connected to the

amplifier.

b) Turn on amp and listen to speakers.

If buzz has changed or reduced in level, then the problem

is coming to the amp from another source. The rest of the

hum you hear is normal and related to the fact that the

RCAs are open ended and not connected to any thing.

c) If above steps do not isolate your problem: star-ground all

components except amplifier from their chassis to the

processor.

Front LEDs are ON all the time

It is normal when running the amplifier to full power that the LEDs

flicker. If you see that the LEDs are on constantly without

flickering (solid orange) it means that the amplifier is clipping.

Reduce volume level toprevent damage tothe unit.

Turn amplifier ON and circuit breaker shuts down

This can either be a short in amp or poor circuit breaker in the

house. Plug amplifier into another outlet on a different circuit

breaker with nothing connected. If the amp turns on then the

problem is with your home circuit breaker. If the amplifier still does

not power up, please call Earthquake toconsult with a technician.

If you are still stuck...

1. Contact an authorized Earthquake Dealer.

2. Contact Earthquake Sound Customer Service at 800-576-7944

Note:

Visit www.earthquakesound.com for answers to frequently asked

questions and additional troubleshooting information.

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Cinénova-IR16 Power Amplifier

Product Warranty

Five (5) year limited warranty

Earthquake warrants the original purchaser that all Factory Sealed New Audio

Products to be free from defects in material and workmanship under normal

and proper use for a period of five (5) years from the date of purchase (as shown

on the original bill of sale with serial number affixed/written on it). The five (5)

year warranty period is valid only if an authorized Earthquake dealer properly

installs the product and the warranty registration card is properly filled out and

sent to Earthquake Sound Corporation. If a non-authorized party installs the

product, a ninety (90) day warranty period will be applied.

surround & dust cap, burnt speaker voice coil.

• Fading and or deterioration of speaker components & finish due to

improper exposure to elements.

• Bent amplifier casing, damaged finish on the casing due to abuse, misuse

or improper use of cleaning material.

• Burnt tracers on PCB.

• Product/part damaged due to poor packaging or abusive shipping

conditions.

• Subsequent damage to other products.

(A) Five (5) years limited warranty plan coverage guidelines:

warranty claim will not be valid if the warranty registration card is not

properly filled & returned to Earthquake with a copy of the sales invoice.

Warranty card is located on the last page of this manual.

• Firstyear: Earthquake pays for labor, parts, and ground freight (only in US

mainland, not includingAlaska and Hawaii) (shipping tous is not covered).

• Secondyear: Earthquake pays forlabor and parts only, customer must pay

freight both ways.

• Third, fourth& fifthyear: Earthquake pays labor only. Customer must pay

forparts and freight both ways.

(E) Service Request:

To receive product service, contact Earthquake service department at (510)

732-1000 and request an RMA number (Return Material Authorization). Items

shipped without a valid RMAnumber will be refused. Make sure you provide us

with your complete/correct shipping address, a valid phone number, and a brief

description of the problem you are experiencing with the product. In most cases,

our technicians might be able to resolve the problem over the phone; thus,

eliminating the need toship the product.

(B) Warning:

Products (sent for repair) that are tested by Earthquake technicians and

deemed to have no problem(s) will not be covered by the five (5) year limited

warranty. Customer will be charged a minimum of one (1) hour of labor (at the

ongoing rates) plus shipping charges back tocustomer.

(F) Shipping Instructions:

products/parts subject to the following provisions:

Product(s) must be packaged in its original protective box(es) to minimize

transport damage. Shipper claims regarding items damaged in transit must be

presented to carrier. Earthquake Sound Corporation reserves the right to refuse

improperly packed product. Original bill of sale must accompany product

returned for service. We encourage you to include with the package a written

description of the problem. Ship product to: Earthquake Sound Corp. 2727

McConeAvenue, Hayward, CA94545. Ph (510) 732-1000. You are responsible

forthe cost of shipping the product toEarthquake Sound Corporation.

• Defective products/parts have not been altered or repaired by other than an

Earthquake factory-approved technician.

• Products/parts are not subjected to negligence, misuse, improper use or

accident, damaged by improper line voltage, used with incompatible products

or have its serial number or any part of it altered, defaced or removed, or have

been used in any way that is contrary toEarthquake's written instructions.

(D) Warranty Limitations:

(G) Disputes Resolution:

Warranty does not cover products that have been modified or abused,

including but not limited to the following:

• Damages to speaker cabinet and cabinet finish due to misuse, abuse or

improper use of cleaning materials/methods.

All disputes - between clients and Earthquake Sound Corporation - resulting

from the five (5) years limited warranty policy must be resolved according to the

laws &regulations of the county ofAlameda -California.

• Bent speaker frame, broken speaker connectors, holes in speaker cone,

We recommend that you place or write

your serial number here for future

reference, if necessary.

PRODUCT REGISTRATION

This Cinénova-IR16 PowerAmplifier can be registered by returning the Product Registration card attached to this

manual or by visiting www.earthquakesound.com. Please also retain the bill of sale, which represents proof of

purchase and helps expedite warranty issues.

SERIAL NUMBER

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.

Sound That Will Move You.

Earthquake Sound reserves the right to amend details of the specifications without notice

Earthquake Sound Corporation | 2727 McCone Avenue. Hayward, CA 94545 | Phone: 510-732-1000 Fax: 510-732-1095

Pobierz from Www.Somanuals.com. All Manuals Search And Pobierz.